PET-Laminated Aluminum Foil Shielding Tape

STS

Product Overview

PET-Laminated Aluminum Foil Shielding Tape

Displays, motherboards, and flex circuits leave little room, yet the shielding still has to block EMI and fit narrow bond areas. STS laminates aluminum foil with a matte black insulating PET film and a black conductive adhesive to provide EMI shielding, light blocking, and ESD grounding.

The single-layer aluminum foil construction is thin and fits small bond areas, and the conductive adhesive provides a direct ground path. The tape resists abrasion, is easy to convert and apply, and is suited for displays, motherboards, shield cans, FPCs and flat cables, and automotive electronics. Shielding performance depends on the assembly structure and the substrate, so test a sample before design-in. The data below applies to P/N STS 50.

Key Features

  • Operating temperature −40 °C to 100 °C (STS 50): suitable for the operating environments of general electronic components
  • Shielding effectiveness >70 dB: 30 MHz to 6 GHz, tested to GB/T 30142-2013
  • Thickness 0.05 mm: thin profile for small bond areas and tight spaces
  • Surface resistance ≤0.3 Ω/inch²: conductive adhesive side for grounding and ESD dissipation
  • Peel adhesion ≥1,500 gf/25 mm: tested to PSTC-101; holding power >24 h (0.5 kg)

Engineering Drawing

STS PET-laminated aluminum foil EMI shielding tape material structure

Material structure (top to bottom): matte black insulating PET / aluminum foil / black conductive adhesive / release liner

Technical Specifications

Property Value Test Method
P/N STS 50 —
Color Black Visual
Foil Construction Single aluminum foil layer —
Thickness 0.05 ± 0.01 mm ASTM D3652
Surface Resistance (adhesive side) ≤ 0.3 Ω/inch² ASTM D257
Coating Abrasion Resistance > 20 cycles ASTM D2210
Coating Ethanol Resistance > 20 cycles ASTM D2210
Shielding Effectiveness (30 MHz–6 GHz) > 70 dB GB/T 30142-2013
Peel Adhesion ≥ 1,500 gf/25 mm PSTC-101
Holding Power > 24 h (0.5 kg) PSTC-107
Roll Size (W × L) 500 mm × 50 m —
Operating Temperature −40 °C to 100 °C —

Specifications above are for P/N STS 50. Values are laboratory averages measured at 23 ± 5 °C and 55 ± 10% RH; individual results may vary slightly. For other specifications, use the contact form or click "Send Email" above.

Test a Sample First

Shielding performance depends on where the tape is applied, the substrate, and the assembly structure, so validate a sample under actual assembly conditions. Use the contact form or click "Send Email" above and share your application, bond area, and shielding requirements. The sales team will arrange samples and an evaluation.

Applications

🖥️

Displays and Motherboards

The thin foil construction bonds around display panels and motherboards to help suppress EMI and maintain signal integrity.

🔌

FPCs and Flat Cables

Wraps flat cables with small bond areas, while the conductive adhesive provides a ground path for ESD.

🚗

Shield Cans and Automotive Electronics

With an operating range of −40 °C to 100 °C, the tape is suited for reinforcing board-level shield cans and shielding automotive electronic components.

FAQ

Q1|What is the EMI shielding effectiveness of STS?

P/N STS 50 provides >70 dB of shielding from 30 MHz to 6 GHz, tested to GB/T 30142-2013. This is a laboratory average. Actual results vary with the bonding method and the substrate structure, so test a sample before design-in. Use the contact form or click "Send Email" above to get in touch.

Q2|How do I apply the tape for the best adhesion?

Make sure the substrate is clean and dry, with all oil, moisture, and dust removed. Apply firm pressure with a roller or press. After application, avoid stretching, shear loads, or peel forces for at least several hours so the bond can fully build. Initial tack and aging behavior vary by application, so test the tape under your actual conditions first.

Q3|How should the tape be stored, and what is the shelf life?

Store the tape in its original packaging or carton in a cool place away from direct sunlight. In unopened packaging at 23 ± 5 °C and 55 ± 10% RH, shelf life is 6 months from the date of manufacture.

Q4|What roll sizes are available, and can I order other widths?

The standard roll is 500 mm wide × 50 m long. For other widths, lengths, or converting needs, use the contact form or click "Send Email" above and include your application and required dimensions. The sales team will follow up.

Q5|Can I request a sample first?

Yes. Use the contact form or click "Send Email" above and describe where the tape will be applied and your requirements, so the sales team can help with the evaluation.

Features

{{ typeOne.merge }}
{{ itemOneTitle }}
{{ item }}

Specifications

{{ typeTwo.merge }}
{{ itemTwoTitle }}
{{ item }}
{{ typeThree.merge }}
{{ itemThreeTitle }}
{{ item }}